Produtos
Painéis metálicos lineares para tectos do Centro de Convenções
If you're planning a linear ceiling for a convention center exhibition hall, the first decision that actually matters isn't finish or color — it's which direction the strips should run relative to your hall's booth layout grid. Most convention centers organize exhibitor booths on a standard grid, often 3m×3m or similar, and if your strip direction doesn't relate sensibly to that grid, you end up with a ceiling pattern that visually fights the floor layout instead of supporting it. Run strips parallel to your main aisle direction and the ceiling reinforces the show's circulation logic; run them perpendicular or at an unrelated angle to save on structural coordination, and exhibitors setting up booths often end up working against a ceiling pattern that doesn't relate to anything happening below it.
The second thing worth deciding early: whether strip direction should follow your hall's structural span (which is usually the cheaper, simpler installation) or your booth grid (which usually looks more intentional but may require additional carrier rail engineering if it doesn't align with the structural bay spacing). For a single-purpose exhibition hall that's rarely reconfigured, following the structural span is often the pragmatic choice. For a hall that regularly hosts different show layouts with different booth orientations, a strip direction independent of the structural grid gives you more flexibility, at some additional installation cost.
Procura tectos e fachadas de alumínio personalizados? Vamos conversar
Apresentação da aplicação do produto
Once direction is settled, think about groove spacing in terms of how the space actually gets used, not just how it looks empty. A wide-open groove pattern looks striking in renderings and in an empty hall walkthrough, but once trade show lighting rigs, banner drops, and rigging points are hung from the structure above, a more open groove gives riggers and technicians better visual access to what they’re attaching things to — which is a genuine functional argument for open groove spacing in exhibition halls, not just an aesthetic preference. If your hall does frequent banquet or ballroom conversions in addition to exhibition use, ask your supplier about coating options that hold up to both use profiles, since banquet lighting design (warmer, more decorative) and trade show lighting (utilitarian, rig-mounted) put different demands on a ceiling finish.
Also worth confirming directly: how your strip layout interacts with your hall’s movable partition wall tracks, if you have them. A strip run that crosses a partition wall track without accounting for it is a common coordination gap between the ceiling contractor and the partition wall installer — worth resolving on the drawings before either trade starts work.
Instalação do produto
Instruções de instalação de tectos de tiras de alumínio
- Install the hanger rods according to the ceiling layout, keeping all suspension points at the same horizontal level to prevent the strip line from sagging or twisting along its run.
- Fix the main runners securely, then position the carrier rails (or cross-tees) to match the strip spacing and module width specified in the layout drawing.
- Check and adjust the entire frame so the carrier system is level, straight, and square before any strips are hung, since misalignment at this stage will show clearly along a continuous linear run.
- Insert the aluminum strips into the carrier rail one section at a time, working in the correct sequence so each strip locks flush against the next and the gap width stays consistent along the full run.
- Prepare cut-outs and reserved positions for light fixtures, air diffusers, sprinklers, or access panels before or during installation, and use matching trim or closure strips at these openings to keep the line unbroken.
- After all strips are installed, sight down the full run to check for consistent gap spacing, straight alignment, and secure connections, confirming a flat, continuous, and properly finished ceiling line.
The patterns shown here are only part of what’s available in aluminum strip ceiling systems. Strips can be specified as flat, perforated, micro-perforated, or grooved profiles, in open or closed-gap configurations, with or without acoustic backing fleece behind the perforation.
These options are matched to project needs for acoustic control, airflow, lighting coordination, ease of plenum access, and the overall visual rhythm of the ceiling. Strip profile, width, perforation pattern, gap size, and edge return can be customized according to project drawings and design requirements.
The colors shown here represent only part of the available finish options for aluminum strip ceiling systems. A wide range of standard and custom colors is available to support different interior styles, from clean transit and office environments to decorative commercial and hospitality spaces.
Finishes are selected to complement lighting design, coordinate with wall and floor materials, and meet the practical demands of high-traffic public spaces. Whether the project calls for classic white, black, silver, wood grain, or a custom brand color, finish options can be matched to the design intent of the space.
Project-based color selection and custom matching are supported for aluminum strip ceiling systems, helping designers, contractors, and developers align the ceiling finish with the broader architectural palette.
For a hall that rarely changes booth orientation, following the structural span is usually simpler and more cost-effective to install. For a hall hosting varied show layouts, aligning with the booth grid gives more visual consistency across different events, at some additional engineering cost if it doesn't match the structural bay spacing.
Yes, and this is a practical consideration worth raising with your supplier — a more open groove pattern gives riggers better visual access to attachment points above the ceiling than a tightly closed groove would.
It depends on the coating specification — ask your supplier directly about a finish rated for both use profiles if your hall regularly converts between exhibition and banquet configurations, since the lighting design demands differ between the two.
This needs to be resolved at the drawing stage between your ceiling contractor and partition wall installer — a strip run that crosses a wall track without prior coordination is a common and avoidable gap between trades.
Generally yes, since strip runs not aligned to the structural bay spacing require additional carrier rail engineering to support the layout — this is a cost tradeoff worth weighing against the visual or functional benefit of aligning to the booth grid instead.
